Swim-up
On this page you will learn
- why semen must be prepared before IUI or IVF
- how swim-up works
- direct swim-up and swim-up from a washed pellet, and when each is used
- how to perform and time a swim-up at the bench
Why prepare sperm at all?
In natural conception, only a small number of motile sperm leave the seminal plasma and swim through the cervical mucus. Seminal plasma contains prostaglandins, white blood cells, dead sperm and debris, and it contains factors that stop sperm from capacitating. It must never be placed directly in the uterus. Sperm preparation separates motile, normal-looking sperm from the seminal plasma and places them in a clean culture medium, ready for IUI (page 69), IVF (page 24) or ICSI (page 30).
The two standard methods are swim-up, on this page, and density gradient centrifugation (page 11). Page 13 explains how to choose.
How swim-up works
Swim-up uses the sperm's own movement. A layer of culture medium is placed over semen, or over a pellet of washed sperm. Motile sperm swim up out of the semen into the medium; dead and immotile sperm, cells and debris stay below. The top layer is collected after a set time. The method selects for good progressive motility and gives a very clean preparation, but the number of sperm recovered (the yield) is lower than with a density gradient.
Direct swim-up or swim-up from a pellet?
Direct swim-up from semen
Medium is layered directly over liquefied semen, or semen is layered carefully beneath medium. Sperm swim straight out of the seminal plasma. This is the approach preferred in the WHO laboratory manual (6th edition, 2021), because the sperm are never packed into a pellet with leucocytes and dead cells.
Swim-up from a washed pellet
Semen is first diluted with medium and centrifuged, and the medium is layered over the pellet. This is simpler with viscous or low-volume samples, but packing sperm with leucocytes and damaged cells can expose them to reactive oxygen species, which may damage their membranes and DNA. Use it only where your protocol specifies it.
At the bench: a direct swim-up
- Check identity and label all tubes on the body with two identifiers, with a witness (page 3).
- Warm the culture medium to 37 °C. Use a buffered medium suited to where the tubes will stand: a HEPES-buffered medium in air, or a bicarbonate-buffered medium in a CO2 incubator with the caps loosened.
- Assess the liquefied sample first (pages 6-7) so that you know its starting concentration and motility.
- Gently mix the semen. In a round-bottomed or conical sterile tube, carefully layer culture medium on top of a portion of semen, without mixing the two. Using several tubes with small portions gives a larger surface for sperm to swim through.
- Tilt the tubes at about 45 degrees to increase the surface between semen and medium, and incubate at 37 °C for 30 to 60 minutes.
- Without disturbing the interface, gently aspirate the upper layer of medium from each tube with a fresh sterile pipette, and pool them.
- If needed, centrifuge gently to concentrate the sperm and remove excess medium, then resuspend in a small, defined volume of medium for the treatment.
- Assess the final preparation: concentration, motility and the total motile count (page 14).
- Record times, volumes and results, and witness the transfer into the labelled final tube.
When swim-up is a good choice
- Samples with good concentration and motility.
- When a very clean preparation with high motility is wanted, for example for IUI with a good sample.
It is less suitable for samples with low counts, poor motility or heavy debris, where the yield may be too low (page 13).
Common errors
- Mixing the layers when adding medium, so seminal plasma ends up in the harvest.
- Aspirating too deep and collecting the semen interface.
- Using a bicarbonate-buffered medium in tightly closed tubes in room air, so the pH drifts.
- Leaving the tubes at room temperature while you do something else.
- Forgetting to note the incubation time.
Check yourself
- Why must seminal plasma never be placed in the uterus?
- Explain how swim-up selects motile sperm.
- Why does the WHO manual prefer direct swim-up to swim-up from a pellet?
- Why are the tubes tilted during incubation?
Questions on this page
Why is the yield of swim-up lower than a gradient?
Only sperm that swim up into the medium within the incubation time are collected, so fewer sperm are recovered, but those recovered are highly motile and very clean.
Can swim-up be used for a poor sample?
It is usually less suitable for low counts, poor motility or heavy debris. Density gradient centrifugation often gives a higher yield in those samples (pages 11 and 13).
The Genesis ART Textbook is teaching text for trainees and doctors of the Genesis ART Academy. It is not treatment advice and not a laboratory standard operating procedure; every technique is learned under supervision. Page numbers never change.
