Semen analysis I: macroscopic examination (WHO 2021)
On this page you will learn
- how to judge liquefaction and what to do when it is delayed
- how to describe appearance and assess viscosity
- how to measure volume accurately by weighing
- how and when to measure pH
What macroscopic examination is
Before you look down a microscope, you examine the sample with your eyes and with simple tools. This macroscopic examination follows the WHO laboratory manual for human semen (6th edition, 2021). It takes only a few minutes, but errors here, especially in volume, carry through into every number you calculate later.
Liquefaction
Just after ejaculation, semen is a semi-solid coagulum. Prostatic enzymes liquefy it, normally within about 15 minutes at 37 °C. Check the sample at 15 minutes and again at 30. If it has not liquefied by 60 minutes, record this.
A liquefied sample may still contain small jelly-like grains; these are normal and not significant. True delayed or absent liquefaction makes accurate counting impossible. Your laboratory protocol may allow gentle mixing by repeated passage through a wide-bore pipette, or the addition of a proteolytic enzyme approved for this purpose. Whatever you do, record it, because it can affect the result.
Appearance
A normal liquefied sample is grey and slightly opalescent. Record anything different:
- clear or translucent: may indicate a very low sperm concentration,
- red or brown: blood (haemospermia),
- yellow: may follow jaundice, some medicines or a long abstinence, or may reflect infection.
Viscosity
Viscosity is different from liquefaction. A sample can liquefy normally yet remain thick. Draw a little of the sample gently into a wide-bore plastic pipette and let it fall drop by drop under gravity. A normal sample falls in small discrete drops. If it forms a thread more than about 2 cm long, viscosity is raised. High viscosity can interfere with motility, concentration and antibody testing, and with preparation for treatment (page 13).
Volume
Volume is measured most accurately by weighing. Pre-weigh each empty collection container (with its lid), and record the weight on the container. After collection, weigh it again. The difference in grams, taking the density of semen as one gram per millilitre, gives the volume in millilitres.
Do not measure volume by drawing the sample into a pipette or syringe, or by pouring it into a measuring cylinder: part of the sample is left behind and the volume is underestimated. The WHO manual gives the lower reference limit for semen volume as 1.4 millilitres (page 9 explains what a reference limit means).
pH
Measure pH after liquefaction, at a uniform time, preferably within 30 minutes and in any case within one hour of collection, because pH rises as carbon dioxide escapes from the sample. Mix the sample, spread a drop evenly on pH paper with a suitable range, and read the colour against the scale within the time the paper's maker specifies. A pH of 7.2 or above is generally regarded as normal. A low pH with a low volume suggests that seminal vesicle fluid is missing (page 4).
At the bench
- Confirm the label against the worksheet; note times of collection and receipt.
- Place the container at 37 °C. Check liquefaction at 15 and 30 minutes and record the time it is complete.
- Weigh the container and record the volume.
- Note the appearance.
- Mix gently but thoroughly by swirling, without making bubbles. Never shake.
- Assess viscosity with a wide-bore pipette.
- Measure pH.
- Move straight on to the wet preparation for motility (page 7), so that motility is assessed within the hour.
Common errors
- Forgetting to pre-weigh the container, then estimating the volume.
- Measuring pH late, so the reading is falsely high.
- Confusing a thick, liquefied sample with one that has not liquefied.
- Skipping the mixing step: semen is not uniform, and an unmixed sample gives false counts.
- Recording "normal" instead of what you actually saw.
Check yourself
- What is the difference between liquefaction and viscosity?
- Why is weighing the most accurate way to measure semen volume?
- Why must pH be measured within a fixed time after collection?
- What might a clear, translucent sample suggest?
Questions on this page
Does incomplete liquefaction mean the man is infertile?
Not on its own. Delayed liquefaction is recorded and can make testing harder, but the doctor interprets it with the rest of the results and the history.
Why weigh a semen sample rather than pipette it?
Pipetting and pouring leave part of the sample behind, so the volume is underestimated. Weighing the pre-weighed container captures the whole sample.
The Genesis ART Textbook is teaching text for trainees and doctors of the Genesis ART Academy. It is not treatment advice and not a laboratory standard operating procedure; every technique is learned under supervision. Page numbers never change.
