ICSI injection, step by step
On this page you will learn
- how to hold and orient the oocyte for injection
- how to pass through the zona and break the oolemma
- how to deliver the sperm with the least fluid and least damage
- what you record and check after each injection
The principle
The aim is simple to state and takes practice to do well: place one immobilised sperm deep in the ooplasm, with the oolemma truly broken, away from the meiotic spindle, using as little fluid and as little distortion as possible, while keeping the oocyte out of the incubator for the shortest time. Every step below serves one of these aims.
Orienting the oocyte
The second meiotic spindle is usually close to the first polar body, though not always directly under it. To keep the injection pipette away from it, the oocyte is held with the polar body at the 12 o'clock or 6 o'clock position, and the pipette enters at 3 o'clock. Where polarised light imaging is available (page 28), you can see the spindle and position it directly.
At the bench: the injection
- Prepare. The rig is aligned (page 29) and a sperm is immobilised and loaded tail first (page 30). Only now take the MII oocytes from their holding dish and place them in the oocyte drops of the ICSI dish, after checking both dish identities with your witness. Then move the injection pipette into the first oocyte drop.
- Hold. Bring the holding pipette to an oocyte. Use the injection pipette to roll the oocyte gently until the polar body is at 12 or 6 o'clock. Apply light suction to hold it. The oocyte should be held firmly without being sucked in or dented.
- Focus. Focus on the equator of the oocyte so the oolemma at 3 o'clock is a sharp line. Both pipette tips must be sharp in this same plane.
- Position the sperm. Push the sperm forward until it sits just behind the bevel of the injection pipette.
- Through the zona. Advance the pipette at 3 o'clock straight through the zona. You will see the zona give and then the tip pass through.
- Into the ooplasm. Keep advancing towards the far side of the oocyte, about two thirds of the way across. The oolemma usually stretches inwards ahead of the tip, making a funnel.
- Break the oolemma. Apply gentle suction. When the membrane breaks, the ooplasm flows suddenly into the pipette. This sudden flow is your sign of a true break. Stop sucking at once.
- Deliver. Gently push the aspirated ooplasm back into the oocyte, followed by the sperm, with a minimum of PVP. Leave the sperm deep in the ooplasm.
- Withdraw. Withdraw the pipette slowly and smoothly. Watch the entry point: it should close, and the sperm should stay where you placed it.
- Release. Release the suction, let the oocyte go, and move it to a separate area of the drop so injected and uninjected oocytes cannot be confused.
Repeat for each MII oocyte with a fresh immobilised sperm. Inject at a steady pace and do not leave the dish on the stage longer than needed.
After the injection
- Note the time of injection for the dish. The fertilisation check is timed from it (page 33).
- Note anything unusual for each oocyte: very easy or very difficult membrane break, leakage of ooplasm, degeneration. Page 32 covers difficult oocytes.
- Rinse the injected oocytes into pre-equilibrated culture medium in the labelled culture dish, with your witness, and return them to the incubator.
- Change pipettes before the next patient, and record lot numbers.
Why each detail matters
Injecting at 3 o'clock keeps the pipette away from the spindle region. Breaking the membrane with suction makes sure the sperm meets the ooplasm, not a pocket of membrane. Using little fluid and little suction protects the ooplasm and its organisation. Releasing promptly and returning oocytes to culture protects temperature and pH. When fertilisation is poor, these are the first points your supervisor will review on your worksheet (page 34).
Common errors
- Injecting with the polar body near 3 o'clock, so the pipette passes close to the spindle.
- Delivering the sperm before a true break of the oolemma.
- Aspirating a large volume of ooplasm, or injecting a long column of PVP.
- Bringing out more oocytes than you can inject while the dish is on the stage.
Page 34 groups these and other errors so you can trace their causes.
Check yourself
- Where do you place the polar body, and why?
- How do you know that the oolemma has truly broken?
- Why do you note the time of injection?
- List what you record for each oocyte after injection.
Questions on this page
What happens if the oolemma does not break?
If you deliver the sperm without breaking the membrane, it can end up in a pocket of membrane outside the ooplasm and fertilisation may fail. Use gentle suction until you see the sudden flow that shows a true break.
How long should an injection take?
With practice, each injection is short and smooth. The more important rule is that the dish spends as little time out of the incubator as possible; work steadily rather than fast.
Will I inject real oocytes as a trainee?
Training begins on practice material and moves to clinical work only under direct supervision, as your logbook and assessment allow. See page 61.
The Genesis ART Textbook is teaching text for trainees and doctors of the Genesis ART Academy. It is not treatment advice and not a laboratory standard operating procedure; every technique is learned under supervision. Page numbers never change.
