Microfluidic sperm sorting
On this page you will learn
- how microfluidic sperm sorting works without centrifugation
- the possible advantages and the real limits of the method
- how to run a sorting device at the bench
- a brief look at other sperm selection methods and the evidence behind them
The idea
Swim-up and density gradients have been used for decades. Both have drawbacks: swim-up recovers few sperm from poor samples, and centrifugation can expose sperm to reactive oxygen species from leucocytes and damaged cells. Microfluidic sperm sorting tries to select good sperm more gently.
A microfluidic device is a small chip or chamber with very narrow channels or a membrane full of tiny pores. Semen is loaded into an inlet chamber, and culture medium is placed in an outlet chamber above or beside it. Only sperm that can swim actively and progressively through the channels or pores reach the medium. Immotile sperm, cells and debris stay behind. There is no centrifugation, and the method imitates, in a simple way, the narrow paths that sperm travel in the female tract.
Possible advantages
- No centrifugation, so less mechanical stress and less contact with leucocytes in a pellet.
- The selected fraction often has highly motile sperm with normal-looking morphology.
- Several studies report lower DNA fragmentation in the sorted fraction than in the raw sample.
- It is simple, quick to learn and standardised by the device design.
Real limits
- The yield is lower than with a density gradient, so it may not provide enough sperm for IUI from a poor sample.
- It depends on motility: it is not suitable when very few sperm are motile, or for surgically retrieved sperm with poor movement.
- Better laboratory measures, such as lower DNA fragmentation, do not automatically mean better clinical results. Studies comparing pregnancy and live birth outcomes have given mixed results, and the evidence is still developing.
- The devices are single-use and add cost.
Present microfluidic sorting honestly: as a useful tool for some samples and some situations, not as a routine improvement for every couple. The choice of method is part of the laboratory protocol and the clinical plan (page 13).
At the bench
Each device has its own instructions for use, which you must follow exactly. The general sequence is:
- Check identity, label the device and the collection tube on their bodies with two identifiers, and witness (page 3).
- Bring the device and the medium to the specified temperature.
- Assess the liquefied semen (pages 6-7). Very viscous samples may not load well; follow your protocol for viscosity.
- Load the specified volume of semen into the inlet, slowly and without bubbles.
- Add the specified volume of medium to the outlet chamber, again without bubbles.
- Incubate at the stated temperature for the stated time, often around 30 minutes, keeping the device level and undisturbed.
- Collect the medium from the outlet with a fresh sterile pipette, taking care not to draw from the inlet.
- Assess the sorted sample: volume, concentration, motility and total motile count (page 14), and record everything.
Other sperm selection methods
You will hear about several other methods. Each is used for specific situations, and none has replaced standard preparation:
- Magnetic-activated cell sorting (MACS) removes sperm showing an early marker of cell death, using magnetic beads.
- Hyaluronan binding selects sperm that bind hyaluronan, a feature of mature sperm, usually for ICSI.
- High-magnification sperm selection (IMSI) examines sperm at very high magnification before ICSI.
For each of these, laboratory differences are easier to show than clinical benefit. Learn what each does, and treat claims with the same caution as for microfluidics.
Common errors
- Bubbles in the inlet or outlet, which block channels or pores.
- Moving or tilting the device during incubation.
- Drawing from the inlet chamber while collecting.
- Using the method on a sample with very poor motility and then reporting "no sperm recovered".
- Describing the method to patients as if it always gives better results.
Check yourself
- How does a microfluidic device separate motile sperm from the rest?
- Give two advantages and two limits of microfluidic sorting.
- Why does lower DNA fragmentation not automatically mean better clinical results?
- For which kind of sample is microfluidic sorting unsuitable?
Questions on this page
Does microfluidic sorting improve pregnancy chances?
It can select sperm with good motility and often lower DNA fragmentation, but studies of clinical outcomes have given mixed results. It is a tool for some samples, not a routine improvement for all.
Can microfluidics be used for testicular sperm?
Usually not, because the method depends on sperm swimming actively through channels or pores. Surgically retrieved sperm often have poor movement (see page 54).
Do I need a witness when I use a sorting device?
Yes. The device and the collection tube are labelled with two identifiers and the sample transfer is witnessed, exactly as for swim-up or a density gradient (page 3).
The Genesis ART Textbook is teaching text for trainees and doctors of the Genesis ART Academy. It is not treatment advice and not a laboratory standard operating procedure; every technique is learned under supervision. Page numbers never change.
