Slow freezing vs vitrification
On this page you will learn
- How slow (equilibrium) freezing works, step by step
- How vitrification works and why it avoids ice
- The key differences in cryoprotectant, volume, equipment and rate
- Where each method is used today, and open versus closed systems
Two ways round the ice problem
Page 45 explained that cells must be kept from forming ice inside them. There are two ways to do this. Slow freezing removes most of the water from the cell before it can freeze. Vitrification turns the water into a glass so fast that it never forms crystals.
Slow freezing
Slow freezing, also called equilibrium or controlled-rate freezing, uses a relatively low concentration of cryoprotectant. After the cells are equilibrated, they are loaded into straws and placed in a programmable freezer:
- The straws are cooled to a few degrees below zero.
- Ice formation is started deliberately in the medium outside the cells. This is called seeding, and it is done by touching the straw with a very cold instrument.
- The freezer then cools slowly, a fraction of a degree per minute, so water leaves the cells and joins the ice outside.
- At a set low temperature the straws are plunged into liquid nitrogen.
The method needs an expensive freezer and takes a couple of hours, but it uses gentle, low-toxicity solutions. If seeding is missed or the rate is wrong, ice may form inside cells.
Vitrification
Vitrification uses a high concentration of cryoprotectants, a very small volume of solution around the cell, and ultra-rapid cooling by direct or near-direct contact with liquid nitrogen. Under these conditions the solution becomes so viscous that it solidifies as a glass. No ice forms, inside or outside the cell, so the solution-effect injury of slow freezing is avoided.
Because the cryoprotectant concentration is high, its toxicity is the main risk. That is controlled by mixing two permeating agents at lower individual concentrations, exposing cells for short, precisely timed periods, and working in planned steps (page 47 and page 53). The whole process takes minutes and needs no programmable freezer, but it demands skill and exact timing.
The key differences
- Cryoprotectant: low in slow freezing; high in vitrification.
- Volume: larger in slow freezing; very small in vitrification, which speeds cooling.
- Cooling rate: slow and controlled; versus thousands of degrees per minute.
- Ice: formed outside the cell on purpose; versus none at all.
- Equipment: programmable freezer; versus carrier devices and a well-trained hand.
- Operator dependence: lower; versus higher, so training and audit matter more.
Where each is used
Vitrification is now the standard method for oocytes and for embryos, especially blastocysts, in laboratories today, because cells survive the process better and work after warming more like fresh cells. Slow freezing remains in use for sperm (page 54), for which simple protocols work well, and for tissue. You may still meet embryos that were slow-frozen years ago; they must be thawed with the matching slow-freezing protocol, never with a vitrification warming kit.
Open and closed systems
In an open system the drop containing the cell touches liquid nitrogen directly; cooling is fastest. In a closed system the sample is sealed inside a straw or sleeve before it enters liquid nitrogen, which reduces the theoretical risk of contamination through the nitrogen but slows cooling a little; warming must still be very fast. Your laboratory chooses one and validates it; you learn it exactly (page 47).
At the bench
- Look at a programmable freezer and its cooling record from a training run; identify the seeding point and the slow-cooling segment.
- Handle empty open and closed carrier devices; practise labelling and sealing (page 49).
- Find the method used for each sample on a mock cryo-bank inventory sheet, and match it to its warming or thawing protocol.
Common errors
- Warming a slow-frozen embryo with a vitrification warming kit, or the reverse.
- Missing the seeding step in slow freezing.
- Loading too large a volume on a vitrification carrier, which slows cooling.
- Not recording the method on the cryo record.
Check yourself
- What is seeding, and why is it done in slow freezing?
- Why does vitrification need such a small volume?
- Give one advantage and one disadvantage of a closed system.
- Why must the freezing method be recorded on every cryo record?
Questions on this page
Which method is used for oocytes and blastocysts today?
Vitrification is the standard method in modern laboratories for oocytes and embryos. Slow freezing is still used for sperm and tissue.
Can a slow-frozen embryo be warmed with a vitrification kit?
No. Each method has its own matching thaw or warming protocol, which is why the method is recorded on every cryo record.
What is the main risk in vitrification?
The toxicity of the high cryoprotectant concentration. It is controlled by mixing agents, keeping exposures short and exactly timed, and working in steps.
The Genesis ART Textbook is teaching text for trainees and doctors of the Genesis ART Academy. It is not treatment advice and not a laboratory standard operating procedure; every technique is learned under supervision. Page numbers never change.
