Single density gradient I: principle, materials and set-up
On this page you will learn
- why Genesis teaches doctors the single-layer gradient
- how one layer of colloid separates motile sperm
- the full list of materials and equipment
- how media are warmed and the sample is checked before you start
- what goes into the daily quality-control log
Why a single layer
In a single density gradient, the semen sits on one layer of colloid instead of two. There is no second layer to build and no interface between layers to keep sharp. That means fewer steps, less time and fewer chances to make a handling error, which is why Genesis teaches this method to doctors in full. A small comparative study found single-layer methods usable for intrauterine insemination (IUI) preparation, even with low-count samples, and advised choosing the method by the starting quality of the sample.
Source: Jun 2022, Hoa NT et al. (Acta Informatica Medica 30(2):100-104) - The effectiveness of sperm preparation using density mini-gradient and single-layer centrifugation for oligospermia samples
How the layer separates sperm
The colloid is made of silica particles coated with silane, suspended in a medium that matches the salt balance of body fluids. Under centrifugal force, cells move according to their density. Mature, normally formed sperm with tightly packed nuclei are the densest cells, and they are mostly the motile ones. They pass through the layer and collect as a pellet at the bottom.
Seminal plasma, most leucocytes, immature cells, many dead or misshapen sperm and debris are lighter. They stay on top of the layer or at its upper edge. The pellet is then washed to remove the colloid before the sperm are used.
Source: 2021, World Health Organization - WHO laboratory manual for the examination and processing of human semen, sixth edition, section 5.5
Materials and equipment
The kit for one preparation
- Density gradient colloid made for clinical use, within its expiry date; concentration for single-layer use: typical; follow the Heartbeats lab SOP.
- Sperm wash or culture medium with protein, made for assisted reproduction.
- Sterile 15-millilitre conical tubes with caps, at least three: gradient, wash and spare.
- Sterile serological pipettes, sterile transfer pipettes and a pipetting aid.
- A centrifuge with sealed buckets and a chart of revolutions per minute (rpm) against g for that rotor.
- A warm block or incubator, a microscope and a counting chamber.
- Labels, a permanent marker, the worksheet, a timer and protective equipment.
The World Health Organization (WHO) manual asks laboratories to use commercial media manufactured and tested for therapeutic use wherever they are available, and to follow the maker's instructions for gradients. Note the lot number and expiry of each medium on the worksheet so that every product that touched the sample can be traced.
Source: 2021, World Health Organization - WHO laboratory manual for the examination and processing of human semen, sixth edition, sections 5.2 and 5.5
Source: Dec 2015, ESHRE Guideline Group on good practice in IVF labs - Revised guidelines for good practice in IVF laboratories (2015)
Warming and equilibration
Media are used at the temperature in the product sheet, never straight from the refrigerator. Take what you need for one preparation, not the whole bottle, and bring it to that temperature before you start. Match the medium to the place it will stand: a HEPES-buffered medium keeps its pH in room air, while a bicarbonate-buffered medium needs a carbon dioxide incubator. Large opened volumes of gradient can become contaminated; if you ever see microbes under the microscope, discard it.
Source: 2021, World Health Organization - WHO laboratory manual for the examination and processing of human semen, sixth edition, sections 5.2 and 5.5.1
Check the sample before you begin
- Confirm identity and the collection time with your witness (page 24).
- Let the sample liquefy. Warmth at 37 °C and gentle swirling help; if it is still not liquid after 30 minutes, tell the embryologist.
- Check viscosity: let a drop fall from a wide pipette. A thread longer than 2 cm means high viscosity (page 30).
- Measure the volume and take a small drop for the pre-wash count and motility.
Source: 2021, World Health Organization - WHO laboratory manual for the examination and processing of human semen, sixth edition, sections 2.4.2.2 and 2.4.2.3
The daily quality-control log
Before the first preparation of the day, check and record the warm block or incubator temperature, the centrifuge timer and the rpm setting that gives the force in the standard operating procedure (SOP). Write the lot numbers of opened media. A log that is filled every day shows when a piece of equipment starts to drift, long before a sample is harmed.
Source: Dec 2015, ESHRE Guideline Group on good practice in IVF labs - Revised guidelines for good practice in IVF laboratories (2015)
At the bench
Prepare the full kit for one sample on your own and talk the faculty through each item. Fill in the quality-control log for the centrifuge and the warm block. This is hands-on work on training material, signed in your logbook.
Common mistakes
- Using colloid straight from the refrigerator.
- Warming the whole stock bottle again and again.
- Setting rpm without checking the chart for that rotor.
- Starting before the sample has liquefied.
- Leaving lot numbers off the worksheet.
Key points
- Why single: one layer, fewer steps, fewer handling errors.
- Principle: dense, motile sperm pass the layer and form a pellet.
- Before you start: warm media, liquefied sample, volume and pre-wash check.
- Every day: temperature, timer and rpm in the quality-control log.
Check yourself
Answer in your head first, then tap a question to see the short answer.
1. Why is the single layer easier to learn than a double gradient?
There is no second layer to build and no interface to keep sharp, so there are fewer steps and fewer handling errors.
2. What property takes sperm through the layer into the pellet?
Their density: mature, normally formed sperm have a compact nucleus and are the densest cells.
3. Why is the pellet washed after the gradient spin?
To remove the colloid before the sperm are used.
4. Which medium can stand in room air, and which needs a carbon dioxide incubator?
HEPES-buffered medium in air; bicarbonate-buffered medium in a carbon dioxide incubator.
5. What three items go into the daily quality-control log?
Warm block or incubator temperature, centrifuge timer and the rpm for the SOP force; also lot numbers of opened media.
6. From page 24: how far may sample temperature drift?
It should stay between 20 °C and 37 °C.
Training note. Training content for registered medical practitioners. Trainees observe all patient care; they do not treat patients during the programme.
Questions on this page
What is a single density gradient?
A sperm preparation in which semen is layered on one layer of colloid and centrifuged; dense, motile sperm form a pellet that is then washed.
Why is the colloid warmed first?
So that it is used at the temperature the product sheet sets; sperm should never meet colloid straight from the refrigerator.
The Genesis Doctors' Textbook is teaching text for registered medical practitioners on the doctor programmes of the Genesis ART Training Academy. It is not treatment advice and gives no medicine doses; trainees observe all patient care, ultrasound scans are watched only (PCPNDT Act), and bench skills are practised under supervision. Page numbers never change.
