Denudation
On this page you will learn
- why the cumulus and corona cells are removed before ICSI, and why they are left in place for conventional insemination
- how the enzyme step and the mechanical step work together
- how to set up and run a denudation dish safely and quickly
- which handling errors damage oocytes, and how to avoid them
What denudation is and why it is done
When you looked at a cumulus-oocyte complex on page 24, you saw the oocyte buried inside a cloud of cumulus cells, with a tighter layer of corona radiata cells pressed against the zona pellucida. These cells are held together by a gel rich in hyaluronic acid. For conventional insemination they stay in place, because sperm must pass through them naturally. For ICSI they must go. You cannot judge maturity (page 26) until you can see whether a first polar body is present, and you cannot hold an oocyte steady on a holding pipette or place an injection pipette accurately through a layer of cells.
Denudation is the removal of these cells. It has two parts that always go together: a brief exposure to an enzyme of the hyaluronidase class, which loosens the matrix, and gentle mechanical pipetting, which strips the loosened cells away. Neither part alone is enough, and too much of either harms the oocyte.
Timing
ICSI is planned for a window measured from the trigger injection given to the woman (page 22). Denudation sits just before that window. Your laboratory protocol will state when oocytes are denuded relative to pick-up and to the planned injection time, and you follow it exactly. Two principles hold everywhere. First, the oocytes should spend as little time as possible outside the incubator. Second, denude only as many oocytes as you can inject before they need to go back into culture. Record the time of denudation on the worksheet: it is part of the case history the embryologist reviews if fertilisation is poor.
The enzyme step
The enzyme is supplied ready to use in a buffered medium. Exposure is counted in seconds, not minutes. Long exposure does not make the job easier; it raises the risk of damaging the oocyte and, in theory, of activating it without a sperm. The aim is only to loosen the outer cumulus so that pipetting can do the rest.
The mechanical step
Mechanical stripping uses denuding pipettes: fine, smooth-tipped glass or plastic capillaries on a handheld stripper. You begin with a wider bore and move to a narrower one, chosen so the inner diameter is only a little larger than the oocyte with its zona. Too wide and the corona will not come off; too narrow and you squeeze the oocyte, distort the zona and may rupture the oolemma. Draw the oocyte in and out slowly and evenly. Never force it.
At the bench
Set-up. On the day, shortly before the case, prepare a denudation dish as described on page 19: one drop of enzyme solution and several wash drops of buffered handling medium, all under oil and warmed on the heated stage. Label the dish on its base (not only the lid) with the patient identifiers. Have the stripper and pipettes of two or three bore sizes ready, and the ICSI dish already prepared.
Sequence.
- Check the patient identifiers on the culture dish and the denudation dish with your witness before you move any oocyte.
- Transfer a small group of complexes into the enzyme drop with as little medium as possible.
- Pipette them gently a few times, watching the cumulus disperse. Move them out within seconds.
- Rinse through the first wash drop to dilute away the enzyme.
- In the next wash drops, continue with the narrower pipette until the corona is thin enough to see the polar body and the oolemma clearly. A few remaining corona cells are acceptable; a scrubbed-bare zona is not the goal.
- Rinse again, count the oocytes, and assess each one for maturity (page 26).
- Move them to the labelled holding dish of culture medium, record the count and time, and return the dish to the incubator until injection.
What to check. The count before and after denudation must match. If an oocyte is missing, stop and search every drop and the pipette before discarding anything. Each transfer between dishes is a witnessing point (page 3).
Common errors
- Leaving oocytes in the enzyme while you deal with something else.
- Using a pipette that is too narrow, or pipetting fast, so the oocyte is squeezed or lyses.
- Denuding too many oocytes at once and losing track of the count.
- Carrying a large volume of enzyme into the wash drops.
- Letting the dish cool while you search for a lost oocyte, instead of returning the others to the incubator first.
- Over-cleaning the zona until every cell is gone, at the cost of extra handling.
Check yourself
- Why is denudation needed before ICSI but not before conventional insemination?
- What are the two parts of denudation, and what goes wrong if you overdo each one?
- How would you choose the bore of the final denuding pipette?
- Your post-denudation count is one short. What do you do, and in what order?
Questions on this page
Is it harmful to leave some corona cells on the oocyte?
No. A thin layer of corona cells is acceptable as long as you can see the polar body and the oolemma well enough to grade maturity and inject. Removing every last cell adds handling without benefit.
Why is the enzyme exposure so short?
The enzyme only needs to loosen the outer cumulus; the pipette does the rest. Longer exposure adds stress to the oocyte without making stripping easier, so exposure is counted in seconds.
Who checks the dishes during denudation?
A second trained person witnesses each transfer of oocytes between dishes, confirming the patient identifiers match. Page 3 explains witnessing and page 55 covers traceability.
The Genesis ART Textbook is teaching text for trainees and doctors of the Genesis ART Academy. It is not treatment advice and not a laboratory standard operating procedure; every technique is learned under supervision. Page numbers never change.
